Silicone Rubber

SILICONE rubber retains its physical organic elastomers particularly when subjected to extremely low or hightemperatures. It solves design problems that demand elastomersto stay rubber after long exposures of high temperatures. And low temperature properties need not be sacrificed to get maximum heat resistance even the most heat resistant types do not show marked stiffening at temperatures as low as -50°C. Briefly, the mechanical characteristic of SILICONE rubber includes :

  • Good tensile strength at elevated temperatures in comparision to organic rubber SILICONE rubber retains a much greater percentage of its room-temperature tensile strength at high temperatures.
  • "l Good elongation characteristics, ultimate value range to 700 percent.
  • Wide range of hardness 30 to 80 durometer; the designer is free to select a desired hardness that best fits a specific function.
  • Good tear strength - up to 250 ppi and resistance to tear propagation
  • Excellent resistance to compression set at elevated temperatures upto 200° C. Electrically, long term aging at high temperatures produces only minimal change in properties Dielectric stability is relatively unaffected by frequent or extreme temperature fluctuations. Because silicone rubber retains its physical integrity in environmental extremes, electrical failures due to cracked insulation are sharply reduced. When exposed to intense flame, silicone rubber remains nonconducive and does not carbonize. Under environmental extremes SILICONE rubber is unmatched in performance when subjected to weathering, ozone and corona, attack by many oils, chemicals and fungi, low pressure steam, water and radiation exposure.

Components made from SILICONE and FLUROSILICONE rubber are used in almost every major industry. Areas ofgreatest use are aircraft, missiles, automobiles, appliances,electrical machinery, electronic assemblies and spark plug boot.

  • As SILICONE rubber has high dielectric strength and physical toughness, cable connectors, plugs and terminalcovers made from silicone rubber are more reliable thanfrom any other rubber
  • Hybrid SILICONE connectors are used in critical electronics equipment.
  • SILICONE rubber seals, gaskets and '0' Ring s have excellent resistances to compression set and seldom need replace ment e.g. a silicone rubber gasket on a hospital autoclave was finally replaced after exposure to 20 psi steam 5 to 6 hours a day for more than 6 years. Organic rubber gasket lasted only 3 to 4 months
  • Front and rear crank shaft seals made from silicone rubber have been in service for more than 1,50,000 miles on one manufacture's small V-8 service engine for light and medium duty trucks.
  • A patented double lip seal of high performance silicone rubber reduces maintenance and helps insure upto 4,00,000 miles of service life on truck brake actuators.
  • SILICONE rubber radiator and heater hose last 3,00,000 miles in diesel buses and trucks. The hose remains fault free in an environment that causes non silicone hose to break or leak chemicals in the anti freeze, heated air, exhaust gases. wide temperature variations, dust and dirt.
  • In baking plant food handling equipment, SILICONE rubbersuction cups improved handling of all types and shapes of bread and rolls. The cups are bellow shaped for utmostflexibility. Neoprene rubber cups of required flexibility were not sufficiently, resistant to cooking oil and abrasion Nitrile rubber stiffened with heat aging and repeated exposures to detergents.

PRODUCT RANGE

MANUFACTURE OF PRECISION RUBBER PARTS such as : Rubber Sheets Including Insulation Sheets, Oilseals, 'O' Rings, Diaphragms Gaskets, Packings, Grommets, " U " Ram Rings. Chevron Packings, Sponge Sheets, Cords, Sleevings, Beading, panel Door Gaskets, Dam Gate Seals, Protective Rubber Gaurds, Baby Nipples etc.

MOULDED AND EXTRUDED RUBBER PARTS FROM NATURAL, EBONITE, NITRILE,HYPALON BUTYL, EPDM, POLYURETHENE POLY ACRYLIC. SILICONE AND VITON RUBBER FOR YOUR REQUIREMENTS. PLEASE WRITE AT THE ADDRESS GIVEN.